Ir a contenido




Suscríbete!



No te pierdas nada a la vez que nos apoyas desde las redes sociales.

Últimos comentarios


Información del archivo

  • Añadido el: Dec 12 2013 10:26
  • Actualizado el: Dec 12 2013 10:26
  • Tamaño: 327.77K
  • Visitas: 937
  • Descargas: 411

Descargar SPIway 0.20






SPIway v0.20 - Teensy++ 2.0 SPI Flasher
 
Disclaimer
----------
WARNING: Use this software at your own risk. The author accepts no
responsibility for the consequences of your use of this software.
 
Contents:
\SPIway\Release\SPIway.hex - Compiled hex-file for the Teensy++ 2.0 (AT90USB1286)
\SPIway_Installation\SPIway.jpg - Teensy connection points
\serial_install.exe - Teensy serial drivers for Windows
\SPIway.py - SPI PC Python client
\SPIway_Changes.txt - Version history
\SPIway_README.txt - This file
 
--------------------------------------------
Powering option 1 (voltage regulator, Teensy powered by USB):
Install the 3.3V voltage regulator available at pjrc.com! 5V trace has to be cut and 3V pads have to be shorted!
Please refer to https://www.pjrc.com/teensy/3volt.html
 
Only off-board flashing has been tested (desoldered chip).
You should power the chip with Teensy.
Ideally you connect a decoupling capacitor (0.1uF) between GND and Vcc as close to the chip as possible!
Keep the wires short (< 10cm) if you don't use a cap!
--------------------------------------------
 
Prerequisites for Windows:
Python 2.7.2 (http://www.python.org/ftp/python/2.7.2/python-2.7.2.msi)
pyserial 2.5 (http://pypi.python.org/packages/any/p/pyserial/pyserial-2.5.win32.exe)
 
Usage:
Install Python + pyserial (see "Prerequisites for Windows"). Install drivers. Connect Teensy
directly to your PC (not an USB hub, might cause trouble). Flash Teensy with "\SPIway\Release\SPIway.hex"
and reset it after completion. Start Windows' "Device Manager", expand the "Ports (COM & LPT)" node,
you should see something like "USB Serial (Communication Class, Abstract Control Model) (COM4)". This
tells you that "COM4" (or whatever shows up) is the COM port used by Teensy.
 
-SPIway.py
 
* Flash Teensy with "\SPIway\Release\SPIway.hex"
At the command prompt enter "SPIway.py" to display help.
 
first make sure that you are able to read the SPI chip info. Do this by using
the info command.
 
get information:
SPIway.py COMx info
 
dump:
SPIway.py COMx dump filename
 
write:
SPIway.py COMx write filename
 
write with verify:
SPIway.py COMx vwrite filename
 
erase entire chip:
SPIway.py COMx erasechip
 
Support thread:
http://www.ps3hax.net/showthread.php?t=25408
 
More information available at (thanks to eussNL and all contributors for maintaining this great wiki!):
http://www.psdevwiki.com/ps4/SPIway
 
It's tested on Win7 x86/x64, but should also work just fine on any other x86/x64 Windows >=XP. Works as well on
Linux and OS X. Serial drivers are not required for Linux/OS X.
 
Changelog:
 
 
v0.10
-----
+ Initial release
+ Support for Macronix MX25L25635F
 
v0.20
-----
+ Added README
+ Added support for Macronix MX25L1006E
+ Added support for Winbond W25X10CL
 
 
 -- judges (judges@eEcho.com)
 



comments powered by Disqus